Arida Larvik dehumidifier

Save as PDF or print

The environmentally friendly R290 is used as a refrigerant. R290 has no harmful effect on the ozone layer (ODP), a negligible greenhouse effect (GWP) and is available worldwide. Due to its energy-efficient properties, R290 is very well suited as a refrigerant for this use in dehumidifiers. Special precautions must be taken due to the high flammability of the refrigerant.

	This unit uses a flammable refrigerant. If refrigerant leaks and comes into contact with fire or hot parts, harmful gas will be generated and there is a risk of fire.
	Read the instructions carefully before use.
	Further information can be found in the user manual.
	Service personnel must read the operating instructions carefully before use.

Safety instructions

• This appliance is intended for commercial use by private individuals.
• This appliance can be used by children aged from 8 years and above. It can also be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• The unit is designed for use with R-290 (propane gas) as refrigerant only. 
• The refrigerant loop is sealed. Only a qualified technician should attempt service!
• Do not discharge the refrigerant into the atmosphere. R-290 (propane) is flammable and heavier than air.
• It initially collects in low areas but can be circulated by the fans. If propane gas has leaked, do not allow untrained personnel to attempt to find the cause.
• The propane gas used in the unit has no odor.
• If there is an odor from the appliance, this does not indicate that there is a gas leak.
• If a leak is detected, immediately evacuate all persons from the area, ventilate the room, and contact the local fire department to inform them that a propane leak has occurred.
• Do not allow anyone to re-enter the room until the qualified technician advises that it is safe to return to the area.
• Do not use open flames, cigarettes or other possible sources of ignition inside or near this product.
• Component parts are designed for propane and are non-sparking. Component parts should only be replaced with identical repair parts.

It is always important to follow the instructions in this manual. Incorrect use may result in damage to the product, the environment or people.

Precautions for use

To reduce the risk of fire, electric shock, or injury to persons or property, always follow these precautions:

• Do not use outdoors. This dehumidifier is intended for indoor use in residential areas only.
• Do not use the device near walls, curtains, or other objects that may block the air inlet and outlet.
• Keep air intake and outlet free of obstructions.
• If the unit is tilted more than 45°, leave it upright for at least 24 hours before starting up.
• Keep doors and windows closed for better energy savings.
• Do not use or store the device in direct sunlight or rain.
• It is normal for the air outlet to feel warm to the touch after continuous operation on hot days.
• Empty the water tank before moving the unit.
• Make sure the water tank is installed correctly, otherwise the unit will not function properly.
• The dehumidifier starts in the mode that was selected when the unit was last used.
• The dehumidifier starts dehumidifying if the room humidity is 3% higher than the selected humidity.
• There is a protective 3-minute time delay for the compressor. Wait 3 minutes for the dehumidifier to resume dehumidification.
• If the power cord is damaged, it must be replaced by the manufacturer or a qualified person in order to avoid a hazard.
• The appliance must be disconnected from the power supply during maintenance.
• Always operate the device from a power source with the same voltage, frequency, and rating as indicated on the product identification plate.
• Always use a grounded power outlet.
• Unplug the power cord when cleaning or when the device is not in use.
• Do not use the device with wet hands. Avoid spilling water on the device.
• Do not immerse or expose the device to moisture or other liquids.
• Do not tip or overturn the device.
• Do not unplug the unit while it is in operation.
• Do not unplug the power cord by pulling on it.
• Do not use an extension cord or adapter plug.
• Do not place objects or people on the device.
• Do not insert fingers or other objects into the air outlet.
• Do not touch the air intake or aluminum fins on the unit.
• Do not use the device if it has been dropped, damaged, or shows signs of malfunction.
• Do not clean the appliance with chemicals.
• Make sure the device is far away from fire, flammable or explosive objects.
• The device must be installed in accordance with national wiring regulations.
• Do not use agents to accelerate the defrosting process or to clean, other than those recommended by the manufacturer.
• The appliance should be stored in a room without continuous sources of operation (for example: open flames, an operating gas appliance or an operating electric heating system).
• The device must be stored so that mechanical damage does not occur.
• Do not puncture or burn, even after use.
• Please note that refrigerants may not have an odor.
• Pipework shall be protected from physical damage and shall not be installed in an unventilated room, if this room is less than 4m².
• Compliance with national gas regulations must be followed.
• Keep necessary ventilation openings clear of obstructions.
• The appliance should be stored in a well-ventilated area where the room size corresponds to the room area specified for operation.

Product description

Location

1. Place the dehumidifier on a firm, level surface in an area with at least 30 cm of free space around it to allow for proper air circulation.
2. Never place the dehumidifier where it may be exposed to:

• Heat sources such as radiators, heaters, stoves or other products that generate heat.
• In an area where oil or water may splash.
• Direct sunlight.
• Mechanical vibrations or shocks.
• Areas with a lot of dust.
• Lack of ventilation, for example in a closet or bookcase.
• Uneven surface.

Control panel and functions

 POWER

Press the ON/OFF button to turn on the dehumidifier. The default fan speed is high, while the default humidity setting is 50%.
Press the ON/OFF button to turn off the dehumidifier. The compressor will stop immediately, and then the fan will stop after a 30 second delay.

FASHION

Press the mode button to switch between AUTO mode and clothes drying mode (continuous dehumidification). Press and hold the mode button to select night mode.

• AUTO (DROP in display): When the humidity in the room ≥ desired humidity +3%, the fan starts, and the compressor then starts after 3 seconds.
  When the humidity in the room ≤ desired humidity -3%, the compressor stops and the fan stops after a 30 second delay.
  In AUTO mode, both fan speed and desired humidity setting can be adjusted to the desired value.
  After you have set the desired humidity, the LED display will show the current humidity it measures in the room.
• Clothes drying (T-SHIRT in display): The dehumidifier continues to dehumidify continuously, regardless of the humidity in the room. This function is also called continuous dehumidification ("CO").
  The fan speed is adjustable, but the desired humidity cannot be adjusted.
• Night mode: In night mode, the power indicator and sleep indicator will gradually darken if you do not press anything within 10 seconds. Other indicators, lights, and the control panel will turn off.
  Press any button to restore normal function.
  Other functions are the same as in Auto mode.
  In night mode, the dehumidifier will not make a sound when the water tank is full, but the full water tank indicator in the panel (red lamp) will light continuously.

HOURS

Press the timer button to set timer / check timer / cancel timer

• Press TIMER to see the remaining time. The value in the display will flash to show the time. Press the desired humidity button (up arrow) to adjust the timer (0 ~ 24 hours) while the display is still flashing.
• If you want to deactivate the timer, press the TIMER button so that the display flashes and shows the time. While the display is flashing, press the TIMER button again to cancel the timer.
• Press and hold the button to start connecting or disconnecting from WiFi.

FAN SPEED

Press this button to switch the fan speed between high and low speed.

SELECTED HUMIDITY

Press this button to set the desired humidity:
Press once to increase the selected humidity by 5%. The settings are in the following order: 30% – 35% – 40% – 45% – 50% – 55% – 60% – 65% – 70% – 75% – 80% – 30%.

CHILD PROTECTION

Press and hold to turn the child lock function on/off.

When the water tank is full

• The water tank full signal is activated when the water tank has been full for 5 seconds. The water tank full indicator lights up, “88” appears in the display, and “FL” appears on the screen.
• Empty the water tank and place it back in the dehumidifier.

Light indicator

Connecting to WiFi

Preparations

1. Turn on Bluetooth on your phone for faster and easier pairing.
2. Connect the machine to an approved power source.
3. Make sure your mobile device is connected to 2.4G Wi-Fi. The mobile device and the machine must be within good signal strength from the Wi-Fi router.

Download the app

1. Download the app by searching for “Tuya Smart” or “Smart Life” in the App Store or Google Play, and install it.
2. Open the app and sign up or log in to your account.

Connect the dehumidifier to WiFi

1. Turn on the dehumidifier and hold the "TIMER" button for 5 seconds. The WiFi icon will now flash.
   If a smart device is already paired, the icon will turn solid.
2. You can hold the "TIMER" button longer to start a new Wi-Fi pairing.
   This deletes previous pairing.
   If both you and another user are going to control the same device, the original device must be added as yours (or someone else's) as a family member via Family Management in the app.
3. Go to the app's Home screen , tap “Add device” or the plus sign in the top right.
4. Select the correct device from the list and make sure the device is in EZ mode . Follow the instructions in the app to complete pairing.
   The Wi-Fi icon will appear as a solid light when the connection is successful.

Emptying the water tank

• When the tank is full, the dehumidifier will make a beeping sound and the indicator light will light up.
• Pull out the water tank.
• Empty the water into an area with a drain or outdoors.
• Clean the water tank with soap and warm water if the water has been standing still for a long time.
• Place the empty tank back into the dehumidifier.

Using a drain hose

For continuous operation or unattended dehumidification, you can connect the included drain hose. The condensed water can then flow into a bucket or drain by gravity.

• Straighten the drain hose.
• Insert one end of the drain hose into the drain hole and connect the other end to a drain, bucket, or other suitable location.
• If there is a backlash on the hose or the water is blocked, the water container will fill up instead of the hose.

Maintenance

Note: Before cleaning and maintaining the dehumidifier, always make sure it is turned off.

AIR FILTER CLEANING (every other week)
Dust collects on the filter and restricts airflow. The restricted airflow reduces the efficiency of the system and, if blocked, can cause damage to the unit.
The air filter requires regular cleaning. The air filter can be removed for easy cleaning. Do not operate the unit without an air filter as the evaporator may become contaminated.

• Remove the water tank and then pull out the filter from the bottom of the back cover.
• Use a vacuum cleaner to gently suck away the dust on the surface.
  If the filter is very dirty, wash it with water and a mild detergent, then dry it thoroughly.
• Put the filter back in place.
• Do not use agents to accelerate the defrosting process or to clean, other than those recommended by the manufacturer.

Troubleshooting

OPERATING TEMPERATURE
5°C ≤ Ambient temperature ≤ 35°C
When the ambient temperature is lower or higher than the functional temperature, the dehumidifier stops.
When 5°C ≤ Ambient temperature ≤ 16°C, the compressor will automatically defrost at intervals; during defrosting, the compressor stops and the fan continues to run.

Storage and transportation

If you are not going to use the dehumidifier for an extended period of time (more than a few weeks) or transport it, you must clean it and dry it completely.

1. Press the ON/OFF button to turn it off. Wait until the fan has stopped and unplug the power cord.
2. Empty the remaining water from the water tank.
3. Clean the air filter and let it dry.
4. Coil the power cable and place it in the water tank.
5. Put the filter back in place.
6. Store or transport in an upright position.
7. Store the device in a ventilated, dry, non-corrosive and safe place indoors.

NOTE:
The evaporator inside the unit must be dried before packing the dehumidifier away to avoid damage and mold. Unplug the dehumidifier and place it in a dry, open area for a few days to dry it. Another way to dry the unit is to set the humidity more than 5% higher than the ambient humidity to force the fan to dry the evaporator for a few hours.

Connecting to WiFi

Preparations

1. Connect the machine to an approved power source.
2. Make sure your mobile device is connected to 2.4G Wi-Fi. The mobile device and the machine must be within good signal strength from the Wi-Fi router.

Download the app

1. Download the app by searching for “Tuya Smart” or “Smart Life” in the App Store or Google Play, and install it.
2. Open the app and sign up or log in to your account.

Connect the dehumidifier to WiFi

1. When the device is turned on, it will automatically start WiFi pairing for 5 minutes, and the WiFi icon will flash.
   If a smart device is already paired, the icon will turn solid.
2. You can hold the program button for 5 seconds to start a new Wi-Fi pairing.
   This deletes previous pairing.
   If both you and another user are going to control the same device, the original device must be added as yours (or someone else's) as a family member via Family Management in the app.
3. Go to the app's Home screen , tap “Add device” or the plus sign in the top right.
4. Select the correct device from the list and make sure the device is in EZ mode . Follow the instructions in the app to complete pairing.
   The Wi-Fi icon will appear as a solid light when the connection is successful.
5. Turn on Bluetooth on your phone for faster and easier pairing.